100cc Bike Motor Gas 2 Stroke Engine Racing 100cc Motorize Bicycle Lots Of HP

Type: bike motor engine kit. This bike motor engine kit includes. Racer III 80cc/100cc Engine Slant Head - 4.5HP+.

GT80 Reed Valve & Keihin Carburetor Clone Assembly. Magneto With Solid State CDI Ignition. 44Tooth, 9 Hole Chrome Sprocket.

2.0 Liter Fuel Tank, Tear Drop Shape (Black Color). Push Button Clutch Lever And Cable. Twist Throttle With Engine Kill Switch. Idler Pulley Chain Tensioner with Bearings. Needle Bearings On Piston Wrist Pin.

All The Mounting Brackets, Gaskets, And Hardware Including Nylon Locking Nuts. Extra Standard Slant Cylinder Head.

Upgraded bearings / 60% thicker crank case around bearings. Large intake port (40mm bolt hole width). 40mm crank stroke (more powerful, efficient, and reliable).

Type B piston (high wrist pin). Larger 8mm x 1.25 engine mount studs. 50mm bore single piece cylinder/head (increased weight capacity, lower operating temps, easier starting, sustained power output across varied rpm range). Comes with GT80 Reed Valve & Keihin Carburetor Clone Assembly. High performance CDI with Yamaha components.

Bicycle Requirements: This bicycle motor engine kit fits most Mens 24" and larger bicycles which includes mountain, cruiser, chopper and road bikes with a V-frame with at least a 8.5" height clearance for the engine. Larger frame size requires drilling into bike frame and use of the universal face plate. Gas And Oil Mixture For Fuel Ratio: Use of a synthetic 2 stroke oil is recommended. This bicycle motor engine kit is a 2 cycle/2 stroke design, therefore, a gasoline/oil mixture is necessary as follows. When New: 16 to 1 (8oz per Gallon). After 2 Tanks Of Break In: 32 to 1 (4oz per Gallon). The engine crankshaft bearings are lubricated from the oil in the gas mix. A rich break in oil mixture ensures bearings will not cease during engine break in period.

How much weight will this engine kit add to a bike? The engine kits will add about 26 lbs to your bike. Note: We suggest a 26 Men's standard V frame bike. What fuel do I use for this engine kit?

This 2 stroke stroke motor kit requires an Oil and Gas Mixture as follows. You should get 100-150 Miles per gallon and achieve 30-40 MPH depending on climate, altitude, bike weight and rider weight. How do I start and stop my bike with the Raw Racer III?

The starting and stopping of this two stroke motor kits is this. You can still pedal bike like normal with clutch lever held in or locked in with button. To Start: It's just like riding a bike normally, hold in the clutch and pedal the bike to get some speed, then release the clutch to "Jump Start" the motor. If you know of or remember jump starting a Manual VW Bug this start method is the same. To Stop: While the engine is running you can hold in the clutch and the engine will idle.

Push the Kill Switch on the throttle to kill the motor. The clutch must be held in when the bike is in motion or the motor will keep running. Our gasoline operated products are NOT compliant with Environmental Protection Agency E. Or California Air Resources Board (C. B) for the use on/off Public roads.

Top end Needs to be assembled for this engine kit. Due to the difference between different monitors, the picture may not reflect the actual color of the item. The item "100cc Bike Motor Gas 2 Stroke Engine Racing 100cc Motorize Bicycle Lots Of HP" is in sale since Thursday, February 20, 2020. This item is in the category "eBay Motors\Parts & Accessories\Motorcycle Parts\Other Motorcycle Parts".

The seller is "magicalstore99" and is located in Los Angeles, California. This item can be shipped to United States, Canada.

Brand: Unbranded
Manufacturer Part Number: Does Not Apply
Engine: 100cc 2 Cycle Stroke
Warranty: Yes
Type: Bike Engine Kit